£3,000 - £5,000
WITHDRAWN UNTIL 27TH OCTOBER
STAR WARS: A NEW HOPE. RARE & IMPORTANT ONE OF ONE 1976 PROTOTYPE STORMTROOPER HELMET MADE BY ANDREW AINSWORTH, ‘Greeblies Back’ variant, painted vacu-formed plastic, three sectioned, rubber trim brow and underside. Signed ‘Star Wars, 1976’ & Andrew Ainsworth to Interior. Housed in mounted square Perspex case and three additional plaster moulds that would be snapped of from the back internally.
N.B. the property of Andrew Ainsworth who set up Shepperton Design Studios in 1974.
This particular ‘Greeblies Back’ model is only one of one in existence recorded at Elstree Studios in 1976. The Rear Greeblies were derived from John Mollo’s sketch but were later dropped from the final version but the design was repurposed to be used on the sleave of the X Wing Flight Uniform and early Tie Fighter Pilot Helmets.
Andrew went on to create over 200 costumes and characters for A New Hope , the history of which can be seen on his website: OriginalStormtrooper.com
The importance of Prototypes for the film Star Wars; Cost Effectiveness.
Disclosure document 219 presented by Lucas for the copyright court case against
Andrew can assist to explain the importance of creating helmets and costumes very
quickly and cost effectively.
Lucas used outside contractors to fulfil the brief as well as whatever props Elstree
Studios could provide. For example ’Set Model Builders’ Liz Moore & Brian Muir
produced a few of the overall cast compared to Andrew as an outside contractor.
Indeed the £30,000 paid to Andrew was for over 200 helmets and costumes.
The budget for making the Stormtrooper was £1,000 but Andrew sold Stormtrooper
helmets to Lucas for £20 each, and so this level of cost effectiveness proved vital in
staying within budget.
Speed of delivery
John Mollo stated in an interview ,that the production was on a shoe string with ‘Make
do and mend’ as the order of the day.
The only illustration Andrew ever received for the whole film was the small illustration of
a Stormtrooper as a minor character in a large hanger by Ralph McQuarrie This was
good enough for Andrew to interpret the slick, organic character that he produced,
although not quite the metal mechanical droid depicted in the illustration. However,
Lucas accepted ,if not quite liked this offering ,and so it became part of the film.
The studios e orts at that point were all abandoned.
Andrew only ever received verbal requests from either John Mollow or George Lucas.
Foe example, John rang up one day and asked for two black and three white new
characters. Ie: two baddies and three goodies. Maybe with sort of Samurai feel or
another with a long chin. As Andrew had no idea what the story line was about or where
these characters fitted in, he invoiced the two black helmets as Cheese grater and
Jawbone. This particular prototype was just free formed plastic sheet to form a back
cowl, and the same turned upside down to form the chin. It became the Imperial
Gunner.
Andrew had the experience of not only quick mould making for vacuum formed plastic
parts but also the ability to manipulate plastics in all sorts of inventive ways, such as
creating the ‘Jawbone helmet’ without sculpting any moulds at all.
Another example is when George Lucas asked Andrew for just a black back to a helmet,
this being for the Tie Fighter Pilot in the final battle scene.
Thinking creatively, Andrew split the X-wing helmet in two, planted the Stormtrooper face
in front, widened the crown with tri prong piece in the front, included blister eyes and
organic breathing pipes and the piece grew in the fearsome Tie Pilot that featured in the
final battle scene.
Again a quick prototype that actually lay around at the studios for a couple of months
before it was finally used.
The ability to make prototypes quickly that sometimes lay around the studios for a
while was all part of the ‘Make do and mend” aspect of the production. The
Stormtrooper helmet on offer in the auction with the greeblie on the back was such a
piece. The ‘greeblie ‘being made and used for the X Wing Pilots costume.
As the Stormtrooper helmet was a slick plastic moulding, not at all like the metal
fabricated character depicted in Ralph McQuarries picture, I gave Lucas the option of
enhancing the helmet with electronic like ‘greeblies’ that might relate a little more to the
picture. The ‘greeblies were a small piece I had already made for the X Wing Pilot
costume and can be seen on every costume. There was no need to improve or replace
this as Lucas preferred the original helmet I had presented to him. Its a poor picture
from the studios but plaster casts of the intended ‘greeblies' are included in the auction.
Thank you to Andrew Ainsworth for providing and helping with the information supplied for The Auction Room London, from one Local Twickenham Institution to another.
Fees apply to the hammer price:
Free Registration
33.6% inc VAT*
Flat Fee Registration
30.00% inc VAT*